- One Project Closer - http://www.oneprojectcloser.com -

Fred & Kim’s Basement Remodel, Flash an Existing Deck

Posted By Ethan On April 16, 2013 @ 7:00 am In Outdoor,Pro Follow | 10 Comments

I’m back with another Pro-Follow update, and today’s article focuses on waterproofing a leaky deck ledger board. A few years ago, Fred and Kim had their small deck replaced with a much larger one. It’s a beautiful deck. Unfortunately, the contractor did not properly flash the ledger board, and Fred discovered a leak in the basement. If you’re a regular reader, you know that Fred and Kim have hired Joe Bianco [1] to remodel the basement, and part of that remodel is to¬†permanently¬†address the leaky ledger board.

DSC_0369

When the deck was built the contractor should have at least installed metal flashing above the ledger board (not to mention a waterproof membrane behind the ledger and silicone on the bolt heads). This didn’t take place, and Fred found a leak where the old deck was situated. As a temporary fix, he loaded the area with silicone to divert water away from the house, and it worked. Now Joe is providing a more permanent solution.

Step 1: Replace Old Sliding Glass Door

Fred and Kim are having the old sliding glass door replaced as well. It’s not part of the problem, but this was an ideal time to remove the old slider and install a new one. If you’re considering replacing a patio door [2], click that link for a detailed tutorial.

DSC_0377

Joe and Frank removed the old door, frame and sill plate.

DSC_0378

DSC_0380

You can see the door was flashed so that was not the source of the leak. This picture also shows the silicone Fred used to seal the top of the ledger board.

DSC_0385

Joe and Frank framed out the rough opening, sealed the sill plate with waterproof adhesive moved the new door into position.

DSC_0393

They leveled the door and screwed it into the rough framing.

DSC_0415

DSC_0425

Next, the guys trimmed the door opening with PVC boards.

DSC_0434

DSC_0441

With the door (mostly) finished, the guys moved on to address the deck.

DSC_0445

Step 2: Block Underside of Deck

When Joe’s crew did a little framing inside the basement [3], he also had them add blocking between all the deck joists.

DSC_0018

Step 3: Measure Board Width Off Siding

Next, Joe and Frank measured off a board width from the house and snapped chalk lines.

DSC_0448

Step 4: Cut and Remove Deck Boards

Frank set his circular saw just deep enough to cut through the deck boards, and he made the cut along the entire length of the deck.

DSC_0456

The guys used this Crescent 18″ indexing pry-bar to pull up all the pieces, and it was perfect for this.

DSC_0466

DSC_0467

Step 5: Fit New Flashing

Next, Joe and Frank fit new flashing along the house, overlapping with the door flashing.

DSC_0471

They also put the new deck boards in place.

DSC_0472

DSC_0479

DSC_0475

Step 6: Screw New Deck Board

Joe and Frank screwed the new deck board and the old deck boards to the blocking underneath.

Pro-Tip: All the fasteners are rated for exterior use.

DSC_0476

Step 7: Cut and Screw PVC Board

Next, the guys cut a chamfer on some PVC board and ripped it to fit just underneath the previous course of siding.

DSC_0002

They screwed the PVC in place.

DSC_0009

Step 8: Seal Edge

After that, the guys sealed the upper edge of the PVC board with silicone.

DSC_0012

Step 9: Prime and Paint

After priming and painting the PVC board, it blends in well with the siding. The new deck boards stand out now, but that’ll change after they weather some.

DSC_0002-2

DSC_0004

DSC_0005


Article printed from One Project Closer: http://www.oneprojectcloser.com

URL to article: http://www.oneprojectcloser.com/flash-an-existing-deck/

URLs in this post:

[1] Joe Bianco: http://www.oneprojectcloser.com/meet-the-pros/

[2] replacing a patio door: http://www.oneprojectcloser.com/how-to-install-a-patio-door/

[3] framing inside the basement: http://www.oneprojectcloser.com/basement-remodel/

Copyright © 2011 One Project Closer. All rights reserved.